T400N Elite
4B Braime T400N Elite
Unique low cost alarm/indicator panel for use with any 4B NTC-type temperature sensors. ADB810, WDB70, and WDB810 series sensors are recommended.
The T400N ELITE is able to accept signals from up to 8 NTC sensors (zones), which are separated into two groups of 4 zones. Each group of sensors is able to cause alarm and shutdown of individual machine when hazardous conditions are detected. There is a total of 2 Alarm and 2 Stop relays. The control unit is housed in a self contained wall mounting enclosure. A test push button on the lid of the control unit provides for full system verification. Alarm and status LEDs provide means of quick location of the alarm condition, and voltage free relay contacts provide separate alarm and shutdown control. An alarm mute push button is provided on the lid of the control unit and additional connections are provided for an external alarm mute functionality. A rotary switch is used to select the temperature alarm value.
Description
Additional information
| Brand |
|---|
UZYSKAJ CENĘ
Aby otrzymać propozycję, wyślij swoją aplikację na adres info@dystrybutor-przemyslowy.pl i określ wymagane stanowiska oraz dane firmy.
Specification
| T4004NV4CAI | T4004NV46CAI | ||
| Input Supply Voltage | 24 VDC (T4004NV4CAI) | 120 to 240 VAC or 24 VDC (T4004NV46CAI) | |
| Alarm Relay Contacts | Zone 1 - 1 Pole Normally Open - 8 A @ 250 VAC | Zone 1 - 1 Pole Normally Open - 8 A @ 250 VAC | |
| Zone 2 - 1 Pole Normally Open - 8 A @ 250 VAC | Zone 2 - 1 Pole Normally Open - 8 A @ 250 VAC | ||
| Stop Relay Contacts | Zone 1 - 1 Pole Normally Open - 8 A @ 250 VAC | Zone 1 - 1 Pole Normally Open - 8 A @ 250 VAC | |
| Zone 2 - 1 Pole Normally Open - 8 A @ 250 VAC | Zone 2 - 1 Pole Normally Open - 8 A @ 250 VAC | ||
| Sensor Inputs | Up To 8 NTC Thermistors | Up To 8 NTC Thermistors | |
| Sensor Supply | 24 VDC - 100 mA Maximum | 24 VDC - 100 mA Maximum | |
| Terminals | Power: 4 mm^2 - 14 AWG Maximum | Power: 4 mm^2 - 14 AWG Maximum | |
| Signals: 2.5 mm^2 - 16 AWG Maximum | Signals: 2.5 mm^2 - 16 AWG Maximum | ||
| Dimensions (H x W x D) | 9.7 x 7.4 x 4 (inches) / 246 x 188 x 102 (mm) | 9.7 x 7.4 x 4 (inches) / 246 x 188 x 102 (mm) | |
| Fixing Centres (H x W) | 8.75 x 4 (inches) / 222 x 102 (mm) | 8.75 x 4 (inches) / 222 x 102 (mm) | |
| Cable Entry | 2 Holes x 25mm Dia | 2 Holes x 25mm Dia | |
| Weight | 3 lbs / 1.3 Kg | 3 lbs / 1.3 Kg | |
| LED Status Indicators | Green LED - Power | Green LED - Power | |
| Green LED - Hot Bearing #1 through #8 | Green LED - Hot Bearing #1 through #8 | ||
| Red LED - Alarm | Red LED - Alarm | ||
| Push Buttons | Mute | Mute | |
| Test | Test | ||
| WARNING | WARNING |
Related products
4B Braime WDB79V3AI WDB7 Lug Style Bearing Sensors
The WDB7 series is a lug style NTC thermistor or platinum RTD (PT100) type for continuous temperature monitoring. It is designed to bolt directly onto a bearing housing, motor, gearbox, or machine casing. The mounting hole is M8 which can be drilled out up to M10 diameter. The sensor can be connected to a PLC or to a hazard monitoring system, such as 4B’s T500 Hotbus Elite, Watchdog Super Elite, or T400 Elite. The connections are not polarity sensitive therefore special connections requirements are eliminated. The WDB7 series is approved for use in ATEX and IECEx Zone 20 dust hazard locations.
4B Braime ADB810V3AI/D8 ADB Series Bearing Sensors
The ADB series have been designed to allow the depth of the sensor to be adjustable depending on your application. A number of versions are available with probe lengths of 50, 100, 200 and 300 mm. The sensors screw directly into a bearing housing through a 1/4” BSPT threaded grease zerk. Each sensor is fitted with a grease zerk to allow lubrication of the bearing without the need for removal of the sensor. The ADB series have NTC or PT100 type thermistors which allow for continuous temperature monitoring.
The sensor is supplied with a 3m attached cable and can be connected to a PLC or to a hazard monitoring system, such as 4B’s Watchdog Super Elite, T500 Hotbus Elite or T400 NTC Elite. The connections are not polarity sensitive therefore special connection requirements are eliminated, and the cable can be extended in the field.
4B Braime ADB819V3AI/D12 ADB Series Bearing Sensors
The ADB series have been designed to allow the depth of the sensor to be adjustable depending on your application. A number of versions are available with probe lengths of 50, 100, 200 and 300 mm. The sensors screw directly into a bearing housing through a 1/4” BSPT threaded grease zerk. Each sensor is fitted with a grease zerk to allow lubrication of the bearing without the need for removal of the sensor. The ADB series have NTC or PT100 type thermistors which allow for continuous temperature monitoring.
The sensor is supplied with a 3m attached cable and can be connected to a PLC or to a hazard monitoring system, such as 4B’s Watchdog Super Elite, T500 Hotbus Elite or T400 NTC Elite. The connections are not polarity sensitive therefore special connection requirements are eliminated, and the cable can be extended in the field.
4B Braime Bulldog
The Bulldog alignment and rip detection switch is an electro-mechanical system designed to detect dangerous misalignment of the conveyor and also detection of belt tear damage. The switch will detect horizontal misalignment of belts when contact is made with the roller, the roller arm will be forced to pivot by the belt activating a switch at 20º to trigger an alarm, and 35º to trigger a shut down procedure of the conveyor. The sensors are usually installed in pairs on opposite sides of the belt.
A steel flexible wire is set below the running conveyor belt approx 20-30mm attached by a rare earth magnet at each end. If the belt is ripped or damaged the wire is pulled away releasing the magnet connection which in turn will activate a switch.
4B Braime WDB74V3AI WDB7 Lug Style Bearing Sensors
The WDB7 series is a lug style NTC thermistor or platinum RTD (PT100) type for continuous temperature monitoring. It is designed to bolt directly onto a bearing housing, motor, gearbox, or machine casing. The mounting hole is M8 which can be drilled out up to M10 diameter. The sensor can be connected to a PLC or to a hazard monitoring system, such as 4B’s T500 Hotbus Elite, Watchdog Super Elite, or T400 Elite. The connections are not polarity sensitive therefore special connections requirements are eliminated. The WDB7 series is approved for use in ATEX and IECEx Zone 20 dust hazard locations.
4B Braime ADB810V3AI ADB Series Bearing Sensors
The ADB series have been designed to allow the depth of the sensor to be adjustable depending on your application. A number of versions are available with probe lengths of 50, 100, 200 and 300 mm. The sensors screw directly into a bearing housing through a 1/4” BSPT threaded grease zerk. Each sensor is fitted with a grease zerk to allow lubrication of the bearing without the need for removal of the sensor. The ADB series have NTC or PT100 type thermistors which allow for continuous temperature monitoring.
The sensor is supplied with a 3m attached cable and can be connected to a PLC or to a hazard monitoring system, such as 4B’s Watchdog Super Elite, T500 Hotbus Elite or T400 NTC Elite. The connections are not polarity sensitive therefore special connection requirements are eliminated, and the cable can be extended in the field.
4B Braime MDB812V3AI MDB Series Bearing Sensors
The MDB series is a range of bearing sensors manufactured to screw directly into a bearing housing through the existing 1/4” BSPT threaded grease zerk (can be installed in 1/8” NPT grease zerk fitting with an adapter). Each sensor is fitted with a grease zerk to allow lubrication of the bearing without the need for removal of the sensor. The sensor is fitted with a M12 connector for use with a separately supplied cable and socket assembly which can be attached connected directly to a PLC or to a hazard monitoring system, such as 4B’s T500 Hotbus Elite, Watchdog Super Elite, or T400 / T400 NTC Elite. The connections are not polarity sensitive therefore special connection requirements are eliminated. Four versions are available, a NTC thermistor model or PT100 type for continuous temperature monitoring, and PTC or Contact thermistor models with five trip points (60°C, 70°C, 80°C).
4B Braime MDB813V3AI MDB Series Bearing Sensors
The MDB series is a range of bearing sensors manufactured to screw directly into a bearing housing through the existing 1/4” BSPT threaded grease zerk (can be installed in 1/8” NPT grease zerk fitting with an adapter). Each sensor is fitted with a grease zerk to allow lubrication of the bearing without the need for removal of the sensor. The sensor is fitted with a M12 connector for use with a separately supplied cable and socket assembly which can be attached connected directly to a PLC or to a hazard monitoring system, such as 4B’s T500 Hotbus Elite, Watchdog Super Elite, or T400 / T400 NTC Elite. The connections are not polarity sensitive therefore special connection requirements are eliminated. Four versions are available, a NTC thermistor model or PT100 type for continuous temperature monitoring, and PTC or Contact thermistor models with five trip points (60°C, 70°C, 80°C).
