Slipswitch
4B Braime M3007 Slipswitch
The M300 Slipswitch is an easy-to-use inductive proximity shaft speed monitoring device with an adjustable 0 – 30 second start-up delay, all housed in a 30 mm diameter moulded body. The self-contained unit has a single set point, which signals when the shaft speed has dropped by 20% of normal running speed. It is used for detecting dangerous slow down and underspeed conditions on conveyors, bucket elevators, air locks, mixers, fans, grinders and many other machines.
No connection is necessary between the sensor and the equipment being monitored. The proximity sensor detects a stud or bolt mounted on a shaft, or other suitable target. Ideally, the target should be of ferrous metal, but non-ferrous metal will be detected at a shorter range. Maximum range of ferrous targets is 8 mm (5/16”) and for non-ferrous targets is 5 mm (6/16”), assuming a 20 mm (3/4”) diameter target. Smaller targets may be used but operating distances will be reduced.
Description
Additional information
| Brand |
|---|
UZYSKAJ CENĘ
Aby otrzymać propozycję, wyślij swoją aplikację na adres info@dystrybutor-przemyslowy.pl i określ wymagane stanowiska oraz dane firmy.
Specification
| | ||
| Specification | Value | |
| Supply Voltage: | 24 to 240 VAC/VDC | |
| Supply Fusing: | Supply to be fused at 500mA maximum | |
| Switching Capacity: | M3003V10AI: 100 mA maximum; M3007V10AI: 60VDC/VAC, 3A | |
| Saturation Voltage: | M3003V10AI: 5.5 Volts maximum (output on); M3007V10AI: N/A | |
| Leakage Current: | M3003V10AI: 1.6 mA maximum (output off); M3007V10AI: N/A | |
| Ambient Temperature: | 5°F (-15°C) to +122°F (+50°C) | |
| Output State: | M3003V10AI: FET; M3007V10AI: SPCO relay | |
| Sensing Range: | 5/16” (8 mm) maximum on ferrous metal at 77°F (25°C) | |
| Input Pulse Range: | 10 to 3,600 pulses per minute (PPM) maximum | |
| Start-Up Delay: | Adjustable - 0 to 30 seconds | |
| Trip Point: | 20% below set speed | |
| Enclosure: | Nylon - ISO threaded 30 mm by 1.5 mm pitch | |
| Relative Humidity: | 90% RH | |
| LED Indicators: | Blue - Target Sensed, Green - Set Speed | |
| Connections: | 2 wire (M3003V10AI) or 5 wire (M3007V10AI), 3m long cable. | |
| Protection: | IP66 |
Related products
4B Braime ADB810V3AI/D8 ADB Series Bearing Sensors
The ADB series have been designed to allow the depth of the sensor to be adjustable depending on your application. A number of versions are available with probe lengths of 50, 100, 200 and 300 mm. The sensors screw directly into a bearing housing through a 1/4” BSPT threaded grease zerk. Each sensor is fitted with a grease zerk to allow lubrication of the bearing without the need for removal of the sensor. The ADB series have NTC or PT100 type thermistors which allow for continuous temperature monitoring.
The sensor is supplied with a 3m attached cable and can be connected to a PLC or to a hazard monitoring system, such as 4B’s Watchdog Super Elite, T500 Hotbus Elite or T400 NTC Elite. The connections are not polarity sensitive therefore special connection requirements are eliminated, and the cable can be extended in the field.
4B Braime MDB819V3AI MDB Series Bearing Sensors
The MDB series is a range of bearing sensors manufactured to screw directly into a bearing housing through the existing 1/4” BSPT threaded grease zerk (can be installed in 1/8” NPT grease zerk fitting with an adapter). Each sensor is fitted with a grease zerk to allow lubrication of the bearing without the need for removal of the sensor. The sensor is fitted with a M12 connector for use with a separately supplied cable and socket assembly which can be attached connected directly to a PLC or to a hazard monitoring system, such as 4B’s T500 Hotbus Elite, Watchdog Super Elite, or T400 / T400 NTC Elite. The connections are not polarity sensitive therefore special connection requirements are eliminated. Four versions are available, a NTC thermistor model or PT100 type for continuous temperature monitoring, and PTC or Contact thermistor models with five trip points (60°C, 70°C, 80°C).
4B Braime WDA Motion Alignment Sensor
Non-contacting extended range magnetic proximity sensor, not affected by dust or material build up, used to detect moving ferrous material up to 100mm away from the sensor. The WDA sensor can be used on bucket elevators to measure speed and alignment by sensing either the metal elevator buckets, or the ferrous bolts attached to plastic buckets. A more specialized use for the WDA switch is as a broken/slack chain detector on drag chain conveyors, or as a non-contact speed switch for screw conveyors. The sensor is used in conjunction with a PLC or with 4B's Watchdog™ Elite or A400 Elite control units. Two output signals are provided: one signal is a pulse output, representing each bucket detected: the second signal is a continuous output when moving buckets are detected.
4B Braime WDB79V3AI WDB7 Lug Style Bearing Sensors
The WDB7 series is a lug style NTC thermistor or platinum RTD (PT100) type for continuous temperature monitoring. It is designed to bolt directly onto a bearing housing, motor, gearbox, or machine casing. The mounting hole is M8 which can be drilled out up to M10 diameter. The sensor can be connected to a PLC or to a hazard monitoring system, such as 4B’s T500 Hotbus Elite, Watchdog Super Elite, or T400 Elite. The connections are not polarity sensitive therefore special connections requirements are eliminated. The WDB7 series is approved for use in ATEX and IECEx Zone 20 dust hazard locations.
4B Braime ADB819V3AI/D12 ADB Series Bearing Sensors
The ADB series have been designed to allow the depth of the sensor to be adjustable depending on your application. A number of versions are available with probe lengths of 50, 100, 200 and 300 mm. The sensors screw directly into a bearing housing through a 1/4” BSPT threaded grease zerk. Each sensor is fitted with a grease zerk to allow lubrication of the bearing without the need for removal of the sensor. The ADB series have NTC or PT100 type thermistors which allow for continuous temperature monitoring.
The sensor is supplied with a 3m attached cable and can be connected to a PLC or to a hazard monitoring system, such as 4B’s Watchdog Super Elite, T500 Hotbus Elite or T400 NTC Elite. The connections are not polarity sensitive therefore special connection requirements are eliminated, and the cable can be extended in the field.
4B Braime MDB810V3AI MDB Series Bearing Sensors
The MDB series is a range of bearing sensors manufactured to screw directly into a bearing housing through the existing 1/4” BSPT threaded grease zerk (can be installed in 1/8” NPT grease zerk fitting with an adapter). Each sensor is fitted with a grease zerk to allow lubrication of the bearing without the need for removal of the sensor. The sensor is fitted with a M12 connector for use with a separately supplied cable and socket assembly which can be attached connected directly to a PLC or to a hazard monitoring system, such as 4B’s T500 Hotbus Elite, Watchdog Super Elite, or T400 / T400 NTC Elite. The connections are not polarity sensitive therefore special connection requirements are eliminated. Four versions are available, a NTC thermistor model or PT100 type for continuous temperature monitoring, and PTC or Contact thermistor models with five trip points (60°C, 70°C, 80°C).
4B Braime Bulldog
The Bulldog alignment and rip detection switch is an electro-mechanical system designed to detect dangerous misalignment of the conveyor and also detection of belt tear damage. The switch will detect horizontal misalignment of belts when contact is made with the roller, the roller arm will be forced to pivot by the belt activating a switch at 20º to trigger an alarm, and 35º to trigger a shut down procedure of the conveyor. The sensors are usually installed in pairs on opposite sides of the belt.
A steel flexible wire is set below the running conveyor belt approx 20-30mm attached by a rare earth magnet at each end. If the belt is ripped or damaged the wire is pulled away releasing the magnet connection which in turn will activate a switch.
4B Braime MDB834V3AI MDB Series Bearing Sensors
The MDB series is a range of bearing sensors manufactured to screw directly into a bearing housing through the existing 1/4” BSPT threaded grease zerk (can be installed in 1/8” NPT grease zerk fitting with an adapter). Each sensor is fitted with a grease zerk to allow lubrication of the bearing without the need for removal of the sensor. The sensor is fitted with a M12 connector for use with a separately supplied cable and socket assembly which can be attached connected directly to a PLC or to a hazard monitoring system, such as 4B’s T500 Hotbus Elite, Watchdog Super Elite, or T400 / T400 NTC Elite. The connections are not polarity sensitive therefore special connection requirements are eliminated. Four versions are available, a NTC thermistor model or PT100 type for continuous temperature monitoring, and PTC or Contact thermistor models with five trip points (60°C, 70°C, 80°C).
